cat1
  • The special function setting of a sprue picker
    The special function setting of a sprue picker 2018-11-20
    The special function of the sprue picker In STOP page, the operator of the sprue picker can press the  key twice to enter PASSWD page as below:  Enter 2011 and press  the operator of the sprue picker will see the page PASSWD1, in which the sprue picker operator will be able to use the Up/Down key to move to each function and modify the setting of them.  Below the functions of the sprue picker in page PASSWD1 for your reference: 1. SafDoor:      NotUse: Not detect safe door signal     Use:      When falling to fetch, can detect injection safe door signal. It will alarm if there is no signal.  2. ClrProd:      Choose whether to clear the existing production, "ON" clear existing production, "OFF" append existing production.  3. StopSta:     NotUse: In STOP status, the ON/OFF signal always output.      Use:       In STOP status, it will forbid the injection OPEN/CLOSE mold if robot received open mold end signal, or you will open and close the safe door one time.  4. RsvTime:      If the program has reserved action, this parameter is times of the reserved action output time. If this parameter is '3', the reserved action will be output every 3 mold. 5. CycTime:      Waiting time of open finish output again after robot finish an auto cycle. If the real time more than the set, it will alarm.  6. Alm Time:      Set alarm time. The alarm will stop if time out, but the alarm screen will be retained.  7. BtnSound:      OFF: No key tone when pressing the key.      ON: It has key tone when pressing the key.  8. OsdStdby:      NotUse: Robot will standby in the of spin in side at AUTO mode. According to the module program action.      Use:      Robot will standby in the of spin out side at AUTO mode. When injection open finish, mold will be executed after spin in.  9. S1DOutSi:     NotUse: Arm falling down at normal speed after spin out at AUTO mode.      Use:      Arm falling down at slow speed after spin out at AUTO mode.  10. CloScrTi:      Set the display sleep time, the minimum is 15s, it will be changed to 15s if the set lower than 15s.  11. ProdtSet:      Plans of the number of products, it will alarm when current product reach to the set. 
    view more
  • The function setting of a sprue picker
    The function setting of a sprue picker 2018-11-20
    The function setting of a sprue picker In the status of STOP and AUTO, press to enter FUNCTION page. The operator of the sprue picker can use up/down key to move to each function and modify the setting or press STOP key to leave Function page and return to Stop page. 1. Language: Language Selection 2. EjectCtrl: NotUse: Allow the long-term output of the thimble signal and will not limit the action of the thimble. Use: The thimble ejection allowed signal would be disabled when the robot start to move and the timing start. The  thimble enable signal would be sent after the delay time. 3. ChkMainFixt: PositPhase: Positive detected fixture switch. Fixture switch signal will be ON when fetch success in AUTO mode. ReverPhase: RP to detect fixture switch. Fixture switch signal will be OFF when Fetch success in AUTO mode. NotUse: The system will not detect the fixture switch. It will not detect the switch signal no matter whether the fetching action  succeed or not. 4. ChkViceFixt: The same as ChkMainFixt. 5. ChkVacuum: NotUse: The system will not detect the vacuum switch signal when the sprue picker is running automatically. Use: The vacuum switch signal would be ON when Fetch succeed  in AUTO mode.
    view more
  • The auto-mode of a sprue picker
    The auto-mode of a sprue picker 2018-11-19
    The auto-running of a sprue picker Press key in Auto Mode, the system will turn into Auto Mode and the sprue picker will in the state of automation prepared with the screen of the controller show below: You can press the START key to run the sprue picker automatically when it's in the state of automation prepared and the screen of the controller will show as below: Below meaning of the parameters on the screen of the controller for your reference: CurrMold: Mode number of the currently selected, Running program in accordance with this model number int the AUTO mode. CyclTime: Record the current automatic cycle with time. ProdSet: The plans of products number, It will alarm when the actual output reaches the set production. FetTime: In the AUTO run-time, Each automatic cycle time from prohibit the injection switch-mode to allow ActFini: The number of complete production ActTime: The actual time of action. CurrAct: The executing action. The operator can press   to enter the page of time setting to modify the time parameters. The operator of the sprue picker can also enter MONITOR, INFO page to view I/O signal and INFO recorded. Press auto key to return to auto page.  In AUTO mode the alarm will occur when fetch failed. The operator of the sprue picker can press Auto Key (or open safe door) to close the alarm and continue. Or press the stop button to back to the origin status and exit auto mode. 
    view more
  • The MANUAL mode of a sprue picker
    The MANUAL mode of a sprue picker 2018-11-19
    The MANUAL mode of a sprue picker Press  key in STOP mold, the system will turn into MANUAL mode. The operator of the sprue picker will be able to perform certain operation with the function keys below:  Main arm rising/falling action, press once more, acting to the other side. Main arm going forward/ backward action, press once more, acting to the other side. Main arm clips on/off. Arm rotating in/out action, press once more, acting to the other side Vacuum sucks on/off . Spare valve on/off the action. Vice arm rising/falling action, press once more, acting to the other side. Vice arm going forward/ backward action, press once more, acting to the other side. Vice arm clip on/off action. Arm single/both select. The manual mode is an important function of the sprue picker during the installation, trial production and repairing. The operation can set the original position, the position of the arm etc in the manual mode. 
    view more
  • The Stop Mode of a Sprue Picker
    The Stop Mode of a Sprue Picker 2018-11-19
    The screen of the controller when the sprue picker is in the STOP mode The controller of the sprue picker will enter the STOP mode after self-testing when power one. It'll also enter the STOP mode if press "STOP" key when in other mode.
    view more
first page 1 2 last page

a total of 2 pages

New Products
Contact Us

Nanwei Industrial District, Chashan Town

Tel : +86 769 82398229
Whatsapp : +8618665171961
Fax : +86 769 81859017
Email : sales@switek.biz
Skype : +8618665171961
Robot Inquiry
Send us the detailed information of your injection molding machine, mould and product to get an instant quotation.
welcome to switek
Send us the detailed information of your injection molding machine, mould and product to get an instant quotation.
   

online service

Home

Products

about

contact